Coats 6450 3D User Manual download pdf (Page 17)

Important: Always read and follow the information box instructions. • 11

Direct Select™ Weight Placement Location

Before spinning the wheel, use direct select to indi-

cate weight placement locations as follows:

Note: When the machine is turned ON, the balancer

defaults to truck mode and 2-plane dynamic mode

using standard clip-on wheel weight locations (Clip 1

and Clip 2) and wheel dimensions.

Clip 1 Top Center - select this location to place a stan-

dard clip weight on the inboard rim flange.

T-1 Tape Top Center - select this location to place an

adhesive weight on the inboard side of the wheel that

is the horizontal plane at the outer edge.

Patch Static - select this location for a patch weight

centered inside the tire. See Patch Weight Balance on

page 13 for further details.

T-2 Tape Laser Locator - select this location to place

an adhesive (hidden) weight on the outboard side of the

wheel that is a horizontal plane in the inner area. See

Laser Guided Operation™ System on page 6 for further

details.

T-3 Tape Top Center - select this location to place an

adhesive weight on the outboard side of the wheel that

is the horizontal plane at the outer edge.

Clip 2 Top Center - select this location to place a stan-

dard clip weight on the outboard rim flange.

Balance Options

The indicator will illuminate to show the active balance

option. Functions are as follows:

Dynamic/Static - press the respective key to cycle

through either a Dynamic, a Dynamic with Total Static

displayed, a Static, or the EB (if feature is available and

enabled, see page 12) balance mode.

LED Indicators

for 6450

LED Status Balance Mode

Both LEDs Lit Dynamic

Top LED Lit Dynamic/Total Static

Bottom LED Lit Static

Behind Spoke - toggle the Behind Spoke option on or

off. See Behind Spoke on page 12 for further details.

Spoke 1/Spoke 2 - toggle to set the Spoke 1 location

and the Spoke 2 location for adhesive weights (hidden

weights).

Information Box

Displays A, W, and D values, functions, and instruc-

tions for the operator. Error messages will also be

shown in this display.

Keypad Group

The operator enters wheel data information, selects

functions, and sets options using these keys.

“Numbered” Keys - use to enter wheel data values.

Cal Mach - press and hold the SHIFT key and press 1

to activate Calibrate Machine mode. See Machine Cali-

bration on page 17 for further details.

Match Balance - press and hold the SHIFT key and

press 5 to select the Match Balance mode. See Match

Balance (Optimization) on page 16 for further details.

Round Off - press and hold the SHIFT key and press 6

to toggle between either roundoff (0.25, 0.50 or 2.00-

ounce) or fine (0.01-ounce) weight increments.

Operator A/B - press and hold the SHIFT key and

press 7 to toggle between two operator memories (A

or B). The default memory is Operator A.

Hood Start - when on, sets the balancer to automati-

cally start the spin cycle as soon as the hood is lowered

completely and the hood safety interlock system is

engaged. Press and hold the SHIFT key and press 8 to

toggle Hood Start on or off. The default is on.

Ounce/Gram - press and hold the SHIFT key and press

9 to toggle between either ounce or gram weight mea-

surements. The default is ounce.

Stop & Exit - press STOP to end a measurement cycle,

exit a function or a mode.

Start - press START to begin a measurement cycle, if

the hood is lowered.

Next - function key used when accessing balancer

instructions and, if balancer is 3D and equipped with

an inverter, automatically rotates tire to its next weight

placement position.

Shift - function key used when accessing balancer

modes or options.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 27 28

Comments to this Manuals

No comments

Coats 6450 3D User Manual Page 17

Comments to this Manuals

Related products and manuals for Equipment Coats 6450 3D