Coats 1001 & 1001SC Balancer User Manual

P.O. Box 3002, 1601 J. P. Hennessy Drive, LaVergne, TN USA 37086 615/641-7533 800/688-6359 Manual Part No.: 8143259HENNESSY INDUSTRIES INC. Man

Electrical PowerConsult a licensed electrical contractor for proper installationto local electrical codes. Power outlets must be enclosed in afloor ra

Initial TestingInitial testing and training are provided by your COATS distrib-utor. Complete instructions for unpacking and installIng your bal-ancer

6 • COATS 1001 Wheel BalancerDirect Drive1. Start button2. INNER weight display.3. INNER position display.4. OUTER position display.5. OUTER weight di

COATS 1001 Wheel Balancer • 7Direct Drive2. OffsetEnter offset distance with this knob.Move distance gauge totouch edge of wheel.Setup for hidden weig

8 • COATS 1001 Wheel BalancerDirect Drive3. Rim WidthEnter wheel width informationwith this knob.Use rim width calipers tomeasure wheel at pointsshown

COATS 1001 Wheel Balancer • 9Direct Drive4. Rim DiameterEnter rim diameter size asread from tire sidewall.Setup for hidden weights on“mag” wheels is t

10 • COATS 1001 Wheel BalancerDirect Drive5. Spin ModeLower Guard Hood Before Starting Spin.Press start button to obtain normal readings. Balancer wil

COATS 1001 Wheel Balancer • 11Direct DriveBalancing Special MAGWheels (AdhesiveWeights)If standard clip weights are to be used, balance as a“standard”

Direct Drive12 • COATS 1001 Wheel BalancerMAGUse Mag Button.Enter rim diameter as readfrom the sidewall.Move distance gauge arm totouch inner edge of

Direct DriveCOATS 1001 Wheel Balancer • 13Note: This method should only be used when the customer requests no visibleweights (outer plane) and there i

ii • COATS 1001 Wheel BalancerDirect Drive

Wheel Mounting OptionsBack Cone Mounting1. Place spring over threaded stud with the large endinside of the faceplate.2. Select a cone that best fits i

COATS 1001 Wheel Balancer • 15Special ProblemsCustomers will occasionally complain of vibration onthe car after balancing. Some possible causes arelis

16 • COATS 1001 Wheel BalancerDirect DriveCalibration Adjustment ProcedureNote: Do not preform Calibration Adjustment whenmotor is excessively hot.1.

COATS 1001 Wheel Balancer • 17Optional Combi AdapterDirect DrivePreventativeMaintenanceDO NOT use a solvent which leaves an oilresidue.NEVER use compr

8143259 01/01 rev. 2 © Copyright 1993, 2001 Hennessy Industries and COATS All Rights Reserved Printed in USA

COATS 1001 Wheel Balancer • iiiTable of ContentsOperator Protective Equipment . . . . . . . . . .ivOwner’s Responsibility . . . . . . . . . . . . . .

Important InformationRubber Manufacturers Association1400 K Street N. W.Washington, DC 20005(202) 682-4800Tire Guides, Inc.The Tire Information Center

COATS 1001 Wheel Balancer • vOwner’s ResponsibilityTo maintain machine and user safety, the responsi-bility of the owner is to read and follow these i

vi • COATS 1001 Wheel BalancerSafetyIMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONSREAD ALL INSTRUCTIONS1. Eye and face protection recommendation

COATS 1001 Wheel Balancer • 1Direct DriveSpecifications• 5/16 Allen Wrench• Single spin dynamic/static, twin plane.• Vertical wheel mounting.• Backcon

2 • COATS 1001 Wheel BalancerDirect DriveInstallation and SetupA factory trained COATS®Service Technician mustperform the install, setup, and initial

COATS 1001 Wheel Balancer • 3Install and tighten the four (4) remaining accessory pegs andhang the accessories.Note: Balancer will not operate properl