Coats 1055 Balancer User Manual

1601 J. P. Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359 Manual Part No.: 8111868 09HENNESSY INDUSTRIES INC. Manufactur

15. Loosen the four 5/16" nuts and raise the control pod sup-port arm. Raise it high enough to allow room for the pod torotate into position and

Connect to PowerYour factory trained COATS®Service Technician should do thefinal check to verify the power installation before connecting thebalancer

Balancer OperationOverviewThis machine is a two-plane, microprocessor-based computerbalancer. Any imbalance in a wheel, either static or dynamic, isre

COATS 950/1025/1050/1055 Wheel Balancer • 7Control PanelKeypad - User enters information and selectsfunction using these keys.Wheel Measurement Displa

Mounting WheelsSelect the most appropriate mounting method for the wheelyou are balancing. Using the proper method ensures securemounting and safe bal

Alternate MountingIf the wheel has a protruding outer hub which will not permitthe use of the pressure cup, or the cup will not permit the hubnut to e

Wheel Data EntryBefore a wheel can be balanced, the size of the wheel must be entered into the computer. The user enters thedata either automatically

COATS 950/1025/1050/1055 Wheel Balancer • 11Dynamic BalancingThe most common mode used forpassenger cars and light trucks.Selecting this mode tells th

12 • COATS 950/1025/1050/1055 Wheel BalancerDirect DriveSelecting BalancingOptionsHood StartThe balancer can be set to automatically start the spincyc

COATS 950/1025/1050/1055 Wheel Balancer • 13Balancing a WheelProcedureThe following steps walk through the balancing procedure.Do not proceed with the

ii • COATS 950/1025/1050/1055SS Wheel BalancerDirect Drive

14 • COATS 950/1025/1050/1055 Wheel BalancerThe balancer will be idle while the tire is being rotated onthe wheel. During these times, another operato

14. Replace the valve core and inflate the tire. Follow the tirechanger manufacturer's instructions for inflation.Remember:If another operator me

16 • COATS 950/1025/1050/1055 Wheel BalancerDirect DriveMaintenance andCalibrationPreventative MaintenanceThe balancer requires only minor maintenance

COATS 950/1025/1050/1055 Wheel Balancer • 17Distance Gauge Calibration1. Securely mount your calibration wheel.2. Press and hold SHIFT and press 0. Th

8111868 09 3/08 © Copyright 1997, 1999, 2000 Hennessy Industries and COATS All Rights Reserved Printed in USA

COATS 950/1025/1050/1055SS Wheel Balancer • iiiTable of ContentsOperator Protective Equipment . . . . . . . . .ivOwner’s Responsibility . . . . . .

SafetyOperator ProtectiveEquipmentPersonal protective equipment helps make tire serv-icing safer. However, equipment does not take theplace of safe op

COATS 950/1025/1050/1055 Wheel Balancer • vOwner’s ResponsibilityTo maintain machine and user safety, the responsi-bility of the owner is to read and

vi • COATS 950/1025/1050/1055 Wheel BalancerSafetyIMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONSREAD ALL INSTRUCTIONS1. Eye and face protection

COATS 950/1025/1050/1055 Wheel Balancer • 1Before You BeginReceivingThe shipment should be thoroughly inspected assoon as it is received. The signed b

2 • COATS 950/1025/1050/1055 Wheel BalancerInstallation and SetupA factory trained COATS®Service Technician must perform theinstall, setup, and initia

4. Lift the balancer off the pallet.5. Open the accessory box and remove the hood assemblyhardware and hood spring.6. Install the hood stop if not alr